Chassis Inspection Plate Kit - 2701

A remedy recommended for many Classic Volkswagen's is the clutch tube coming loose from the stationary bracket inside the chassis tunnel. For years, the hole saw, air chisel, was used to cut open the chassis and hose clamp or zip tie the tube back to the bracket. Now, you can fix it correctly with the Chassis Inspection Plate Kit. Cutting and welding are needed to do this job perfectly.

Made in the USA | Product updated 6/9/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video | Tools Needed

More Information

Normally In stock - Will Ship ASAP
94 in stock!

Late VW Front Beam Inspection Plate - 2711

Every area of the Classic Volkswagen is an opportunity for greater detail. The inspection plate for late Type 1's is no different and allows for removing the shift linkage from the vehicle. This plate is water jet cut out of aluminum, anodized, and then laser etched with a new seal and stainless steel hardware for the perfect look!

Made in the USA | Product updated 6/9/23 by Pete

Typical time to install - 10 Minutes | Install PDF Link | Install Video | Tools Needed

More Information

Normally In stock - Will Ship ASAP
10 in stock!

Six Shooter Clutch Adjustment Nut - 2820

There is a wing nut that, when functioning at its best, is a FIVE-out-of-TEN experience. This original nut would allow the VW owner to adjust his clutch feel to get the right amount of pedal to disengage the clutch. But most of the time, the OEM German wingnut is no longer on the vehicle, and a Chinese soft nut was chosen, and it feels like a week of not shaving your face. Heck, have you ever tried to adjust it when it was cold outside and you were twisting this wing nut, only for you to miss a twist, and like a propeller, it slaps your finger to the point of you letting out a Go#$&#)$)*_#@)_*$*it!!! Ya, we have all been there. We gave this trick little product a pretty cool name. Yeah, I am biased. We call it the Six Shooter Clutch Adjuster.

Available in Raw Steel, Powder Coated Black, Stainless Steel and NOW, Titanium!!!

Made in the USA | Product updated 11/21/23 by Pete

Typical time to install - 1/2 Hour | Install Guide | Install Video | Tools Needed

More Information

Normally In stock - Will Ship ASAP
99 in stock!

Stainless Steel Shock Bolt Kit - 2890

When updating the details on your rear shocks, you could use your old Kamax hardware, okay, OR you can replace it with some detail-oriented stainless steel hardware from the PRO's at Airkewld. You have watched the videos and seen the chassis builds, and now, you can use the same hardware and outfit your Classic Volkswagen with some premium hardware.

Assembled in the USA | Product updated 6/16/23 by Pete

Typical time to install - 1/2 Hour | Install PDF Link | Install Video | Tools Needed

More Information

Normally In stock - Will Ship ASAP
10 in stock!

Install Brakes onto Ball Joint PRObuilt Beam - 9825

Once you have added the install to your cart, click the following kits that make sense for your build.

1966-1968 - Link
1969-1977 - Link
Type 3 - Link

Installed to Order

Seat Belt Anchor Reinforcement Kit - 2707

The Seat Belt. A fender washer is the most crucial part of keeping you in your place when driving. That's right. If you purchase seat belts, they come with eye bolts and a fender washer. Really? There has to be a better way, right?

We are introducing our new seat belt reinforcement kit! It is perfect for Classic Volkswagens that don't originally come with seat belts or for the vehicle with their pan halves replaced. Either way, get a clean AND safe look with these new beautifully crafted seat belt reinforcement kits.

Made in the USA | Product updated 6/9/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video | Tools Needed

More Information

Normally In stock - Will Ship ASAP
99 in stock!

IDF Weber Hardline Fuel Line Kit - 8083

The Classic Volkswagen engine bay has a problem with fires. You know it. I know it. But what can we do about it? Eliminate connections, fumes, and weak links in the gas system, and eliminate the worry of an engine fire. Sound good?

You just installed your new/rebuilt VW engine, and it is time to connect your dual Weber IDF's and HPMX's. For years is installing some Gates rubber hose and using hose clamps from Autozone. There has to be a more secure way for this fuel system. Airkewld's Stainless Steel Hardline system is here, and you immediately have faith in your fuel system.

Made in the USA | Product updated 6/25/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video | Tools Needed

More Information

Normally In stock - Will Ship ASAP
10 in stock!

Billet Adjustable Lowered Swing Axle Shock - 2606

These shocks fit the Classic Volkswagen Type 1 Beetle and Karmann Ghia with a Swing Axle rear suspension. Shock absorbers are without a doubt the brains of your suspension. Nothing influences how your car rides and handles more than its shock absorbers. These shocks measure 13.000" extended and 9.150" collapsed.

Two kinds of shocks are provided for our clients. These shocks replace the factory shocks with part number 113413031.

Sport - Soft riding shock great for a lowered VW.
Adjustable - Tunable shock great for the enthusiast that like to get a specific ride out of their VW.

Made in the USA | Product updated 6/21/23 by Pete

Typical time to install - 1 Hour | Install PDF Link | Install Video | Tools Needed

More Information

Normally In stock - Will Ship ASAP
10 in stock!

Complete Stainless Steel Classic VW Chassis Fastener Kit - 2921

When rebuilding your 1966 through 1968 Type 1 Classic Volkswagen Chassis, you could use your old Kamax hardware, okay, OR you can replace it with some detail-oriented stainless steel hardware from the PRO's at Airkewld. You have watched the videos and seen the chassis builds, and now, you can use the same hardware and outfit your Classic Volkswagen with some premium hardware.

Assembled in the USA | Product updated 6/16/23 by Pete

Typical time to install - 3 Hours | Install PDF Link | Install Video | Tools Needed

More Information

Normally In stock - Will Ship ASAP

OEM PRObuilt Pedal Assembly Service - 1450

Debuting on November 24th, 2023, the PRO's are proud to introduce the PRObuilt Pedal Assembly Service! This is a service of your existing pedal assembly, meaning it can not be purchased outright, no exceptions. It is built on LHD (Left Hand Drive) only.

Once purchased, the PRO's will email you a prepaid shipping label to pay for the shipping of your pedal assembly. You can then drop it off at your local FedEx DropOff location or a Walgreens location near you.

Once received, the PRO's will disassemble the pedal assembly and Ammonia Dip all the components to see the conditions of all parts received. If replacement parts are needed, these parts will be an additional cost. Pedal bushings, spring, pads and hardware are included in the purchase of this service. The OEM Clutch Lever will be reused if possible. If not, a replacement clutch shaft will be supplied with the purchase.

All steel parts will be powder coated satin black and the pedal base will be smoothed out, bead blasted and oil soaked for a clean, sano, finish. An option will be to install a early style cruiser pedal to replace the terrible factory pedal option. All standard steel parts will be gun blued.

New Cables are optional. Pictures shown are from our Chassis Builds and only include what is listed above.

More Information

Usually Ships in 2 to 4 Weeks
(Built to Order)

SLC-Fury 17 Inch Billet Wheel - 9117

Fits the following:

• All VW's*
• *With bolt patterns in 5x130mm, 5x4.50 and 5x4.75

PDF Instructions:

• Wheel Options Article - Link
• Wheels only come in 17x7 configurations

The PRO's Recommendations:

• Beetle/Ghia's need a 4" Narrowed beam and short axles, (Standard equipment on pre 65 vehicles) or Narrowed IRS arms (69 and later) to run the wheels staggered. (More wheel lip in the rear)
• 14mm Studs with Acorn seat lug nuts
• P205r40-17 Tires up front, P215r45-17 Tires in the rear
• Check out the details tab for more fitment information

More Information

Estimated 12 Weeks

SLC-Fury 18 Inch Billet Wheel - 9217

Fits the following:

• All VW's*
• *With bolt patterns in 5x130mm, 5x4.50 and 5x4.75

PDF Instructions:

• Wheel Options Article - Link
• Wheels only come in 18x7 configurations

The PRO's Recommendations:

• Beetle/Ghia's need a 4" Narrowed beam and short axles, (Standard equipment on pre 65 vehicles) or Narrowed IRS arms (69 and later) to run the wheels staggered. (More wheel lip in the rear)
• 14mm Studs with Acorn seat lug nuts
• Check out the details tab for more fitment information

More Information

Estimated 12 Weeks

Stage 1 PRObuilt Adjustable Ball Joint Beam Complete - 2200

The BEST way to adjust a Classic Volkswagen Type 1 with ball joint front suspension (1966 through 1977), up or down, is by installing a Complete PRObuilt Beam. When the PRO's say complete, they mean complete. You will not need anything in addition to this assembly.

The Stage 1 PRObuilt Beam is built on the Ultimate Beam platform. It's made in stock width and up to four inches narrower than OEM to allow for wider wheels, drop spindles, and disc brakes, that add track width.

The complete beam comes as you see it, spindle to spindle, with an entire PRObuilt steering system installed and ready to bolt in and go. For a full list of details included with the beam assembly, visit the Complete Details section here.

Made in the USA | Product updated 6/14/23 by Pete

Typical time to install - 2 1/2 Hours | Install PDF Link | Install Video | Tools Needed

More Information

12 Weeks on Average

PRObuilt Transaxle Performance - Short Axle - 2310

The BEST way to enjoy the shifting experience at a high performance level (not racing) and low RPM's at higher speeds in a 1949 through 1965 Classic Volkswagen Type 1 Beetle and Karmann Ghia is with a PRObuilt Performance Transaxle equipped with *OEM sized Short Axle/Short Spline Axles (SASS). *(It can fit others, see the Complete Details section for more information).

This transaxle is Perfect for a Performance application. Key features of this transaxle are 3.88 Ring and Pinion, overdrive 4th, along with new synchros, bearings and seals in a rebuilt SASS 12 volt platform. It comes with welded gears, steel shift forks, super diff and heavy duty side plate. All transaxles that come from the PRO's are 12 volt and do not come with OIL. The PRO's recommend this oil from LAT or this on Amazon. You will need 3.5 quarts normally. No Core is Needed.

The PRO's offer a few different transaxle's with different axle lengths. This allows us to fit wheels with different offsets onto cars where as they wouldn't normally fit. So it is recommended you pick out your wheels first, run it by the PRO's to see what axle length makes sense, then choose a Cruiser application, (Freeway Flyer) or Performance application (not racing but more aggressive driving).

Assembled in the USA | Product updated 6/24/23 by Pete

Typical time to install - 6 Hours | Install PDF Link | Install Video| Tools Needed

More Information

12 Weeks on Average