Home > Products > Karmann Ghia
Null


This section covers all the more popular products the PRO's at Airkewld produce for it. Simply scroll down to view all the available products.

Some of the more popular products are the assembled #PRObuilt beams, Smoothies and BAD Series Brakes.

Classic VW Complete Air Ride Kit - 1000 Classic VW Complete Air Ride Kit - 1000

A better way to Air Ride a Classic Volkswagen Type 1 with link pin front suspension and swing axle rear suspension (1949 through 1965) is with a Complete Air Ride Kit from Airkewld. It converts the ENTIRE VW from torsion-sprung suspension to air-ride suspension.

The original Air Ride Kit will allow your Classic VW to lower and raise with a toggle, and the tank will auto-fill to be ready the next time you want to make a suspension adjustment.

Lay it in the weeds. Check. Get up a driveway without dragging the vehicle on the ground. Check. A lovely comfortable ride that even momma will enjoy. CHECK!! Isn't it time to finally set your suspension up correctly with a Complete Air Ride kit from the PRO's at Airkewld?

There are three ways to Air Ride your 1949 through 65 Type 1. Good, Better, Best.

Good
- Individually buy parts, based on budget and skill set - no tech support
Better - Purchase this complete kit (beam|spindle options) - Tech Support Included
Best - Complete PRObuilt Kit with everything you would want - Tech Support Included

Made in the USA | Product updated 6/16/23 by Pete

Typical time to install - 16 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

3-5 Business Days on Average
Normal Price $2,725.11
Airkewld Army Price $2,477.37 per Kit
10 in stock!
(1)
Classic VW Complete Air Ride Kit - 1001 Classic VW Complete Air Ride Kit - 1001

A better way to Air Ride a Classic Volkswagen Type 1 with ball joint front suspension and swing axle rear suspension (1966 through 1968) is with a Complete Air Ride Kit from Airkewld. It converts the ENTIRE VW from torsion-sprung suspension to air-ride suspension.

The original Air Ride Kit will allow your Classic VW to lower and raise with a toggle, and the tank will auto-fill to be ready the next time you want to make a suspension adjustment.

Lay it in the weeds. Check. Get up a driveway without dragging the vehicle on the ground. Check. A lovely comfortable ride that even momma will enjoy. CHECK!! Isn't it time to finally set your suspension up correctly with a Complete Air Ride kit from the PRO's at Airkewld?

There are three ways to Air Ride your 1966 through 68 Type 1. Good, Better, Best.

Good
- Individually buy parts, based on budget and skill set - no tech support
Better - Purchase this complete kit (beam|spindle options) - Tech Support Included
Best - Complete PRObuilt Kit with everything you would want - Tech Support Included

Made in the USA | Product updated 6/16/23 by Pete

Typical time to install - 16 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

3-5 Business Days on Average
Normal Price $2,725.11
Airkewld Army Price $2,477.37 per Kit
10 in stock!
(1)
Classic VW Complete Air Ride Kit - 1002 Classic VW Complete Air Ride Kit - 1002

A better way to Air Ride a Classic Volkswagen Type 1 with ball joint front suspension and IRS axle rear suspension (1969 through 1977) is with a Complete Air Ride Kit from Airkewld. It converts the ENTIRE VW from torsion-sprung suspension to air-ride suspension.

The original Air Ride Kit will allow your Classic VW to lower and raise with a toggle, and the tank will auto-fill to be ready the next time you want to make a suspension adjustment.

Lay it in the weeds. Check. Get up a driveway without dragging the vehicle on the ground. Check. A lovely comfortable ride that even momma will enjoy. CHECK!! Isn't it time to finally set your suspension up correctly with a Complete Air Ride kit from the PRO's at Airkewld?

There are three ways to Air Ride your 1969 through 77 Type 1. Good, Better, Best.

Good
- Individually buy parts, based on budget and skill set - no tech support
Better - Purchase this complete kit (beam|spindle options) - Tech Support Included
Best - Complete PRObuilt Kit with everything you would want - Tech Support Included

Made in the USA | Product updated 6/16/23 by Pete

Typical time to install - 16 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

3-5 Business Days on Average
Normal Price $2,372.48
Airkewld Army Price $2,156.80 per Kit
10 in stock!
(2)
Classic VW Front Air Ride Kit - 1100 Classic VW Front Air Ride Kit - 1100

A better way to Air Ride a Classic Volkswagen Type 1 with link pin front suspension (1949 through 1965) is with a Complete Front Air Ride Kit from Airkewld. It converts the ENTIRE front torsion-sprung suspension to air-ride suspension.

Lay it in the weeds. Check. Get up a driveway without dragging the vehicle on the ground. Check. A lovely comfortable ride that even momma will enjoy. CHECK!! Isn't it time to finally set your suspension up correctly with an Air Ride kit from the PRO's at Airkewld?

There are three ways to Air Ride the front of your 1949 through 65 Type 1. Good, Better, Best.

Good
- Individually buy parts, based on budget and skill set - no tech support
Better - Purchase this complete front kit (beam|spindle options and utilize our air management kit) - Tech Support Included
Best - Stage 2 PRObuilt Beam is Bolt-On ready - Tech Support Included if used with our air management kit

Made in the USA | Product updated 6/16/23 by Pete

Typical time to install - 4 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

3-5 Business Days on Average
Normal Price $545.73
Airkewld Army Price $496.12 per Kit
10 in stock!
Classic VW Front Air Ride Kit - 1101 Classic VW Front Air Ride Kit - 1101

A better way to Air Ride a Classic Volkswagen Type 1 with ball joint front suspension (1966 through 1977) is with a Complete Front Air Ride Kit from Airkewld. It converts the ENTIRE front torsion-sprung suspension to air-ride suspension.

Lay it in the weeds. Check. Get up a driveway without dragging the vehicle on the ground. Check. A lovely comfortable ride that even momma will enjoy. CHECK!! Isn't it time to finally set your suspension up correctly with an Air Ride kit from the PRO's at Airkewld?

There are three ways to Air Ride the front of your 1966 through 1977 Type 1. Good, Better, Best.

Good
- Individually buy parts, based on budget and skill set - no tech support
Better - Purchase this complete front kit (beam|spindle options and utilize our air management kit) - Tech Support Included
Best - Stage 2 PRObuilt Beam is Bolt-On ready - Tech Support Included if used with our air management kit

Made in the USA | Product updated 6/16/23 by Pete

Typical time to install - 3 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

3-5 Business Days on Average
Normal Price $563.93
Airkewld Army Price $512.66 per Kit
10 in stock!
(1)
Classic VW Rear Air Ride Kit - 1200 Classic VW Rear Air Ride Kit - 1200

The Best way to Air Ride a Classic Volkswagen Type 1 with swing axle rear suspension (1949 through 1968) is with a Rear Air Ride Kit from Airkewld. It converts the Rear from torsion-sprung suspension to air-ride suspension.

Lay it in the weeds. Check. Get up a driveway without dragging the vehicle on the ground. Check. A lovely comfortable ride that even momma will enjoy. CHECK!! Isn't it time to finally set your suspension up correctly with a Complete Air Ride kit from the PRO's at Airkewld?

There are two ways to Air Ride your 1949 through 68 Type 1. Good, and Best.

Good
- Individually buy parts, based on budget and skill set - No tech support
Best - Purchase this complete kit - Tech Support Included if used with our air management kit

Made in the USA | Product updated 6/16/23 by Pete

Typical time to install - 6 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

3-5 Business Days on Average
Normal Price $1,074.15
Airkewld Army Price $976.50 per Kit
10 in stock!
(8)
Classic VW Rear Air Ride Kit - 1202 Classic VW Rear Air Ride Kit - 1202

The Best way to Air Ride a Classic Volkswagen Type 1 with IRS axle rear suspension (1969 through 1977) is with a Rear Air Ride Kit from Airkewld. It converts the Rear from torsion-sprung suspension to air-ride suspension.

Lay it in the weeds. Check. Get up a driveway without dragging the vehicle on the ground. Check. A lovely comfortable ride that even momma will enjoy. CHECK!! Isn't it time to finally set your suspension up correctly with a Complete Air Ride kit from the PRO's at Airkewld?

There are two ways to Air Ride your 1969 through 77 Type 1. Good, and Best.

Good
- Individually buy parts, based on budget and skill set - No tech support
Best - Purchase this complete kit - Tech Support Included if used with our air management kit

Made in the USA | Product updated 6/17/23 by Pete

Typical time to install - 6 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

3-5 Business Days on Average
Normal Price $727.65
Airkewld Army Price $661.50 per Kit
9 in stock!
(4)
2 Valve Air Management Kit Manual - 1300 2 Valve Air Management Kit Manual - 1300

The Best way to manage Air Ride on a Classic Volkswagen is to have the right parts to do what is needed every time. The Air Management Kit (AMK) will allow your Classic VW to lower and raise with a toggle, and the tank will auto-fill to be ready the next time you want to make a suspension adjustment. A 2-valve AMK will perfectly do a single axle, front or rear. A 4-valve AMK will do the entire VW perfectly.

Lay it in the weeds. Check. Get up a driveway without dragging the vehicle on the ground. Check. A lovely comfortable ride that even momma will enjoy. CHECK!! Isn't it time to finally set your suspension up correctly with a Complete Air Ride kit from the PRO's at Airkewld?

Made in the USA | Product updated 6/17/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

3-5 Business Days on Average
Normal Price $948.54
Airkewld Army Price $862.31 per Kit
10 in stock!
(1)
4 Valve Air Management Kit Manual - 1301 4 Valve Air Management Kit Manual - 1301

The Best way to manage Air Ride on a Classic Volkswagen is to have the right parts to do what is needed every time. The Air Management Kit (AMK) will allow your Classic VW to lower and raise with a toggle, and the tank will auto-fill to be ready the next time you want to make a suspension adjustment. A 4-valve AMK will do the entire VW perfectly. A 2-valve AMK will perfectly do a single axle, front or rear.

Lay it in the weeds. Check. Get up a driveway without dragging the vehicle on the ground. Check. A lovely comfortable ride that even momma will enjoy. CHECK!! Isn't it time to finally set your suspension up correctly with a Complete Air Ride kit from the PRO's at Airkewld?

Made in the USA | Product updated 6/17/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

3-5 Business Days on Average
Normal Price $1,100.13
Airkewld Army Price $1,000.12 per Kit
9 in stock!
(2)
Ultimate Adjustable VW Front Ball Joint Beam - 2100 Ultimate Adjustable VW Front Ball Joint Beam - 2100

A better way to lower a Classic Volkswagen Type 1 with ball joint front suspension (1966 through 1977) other than utilizing adjusters in the center of the beam is to order an Ultimate Adjustable Front Beam.

The Ultimate Beam (UB) allows you to adjust your ride height from stock height down to *seven inches on average. The UB has Delrin bushings, a steering dampener bracket, and grease-able zerks. The UB can come in stock width, up to 4" narrowed with shock towers. New torsions, tie rods, and shocks are recommended for the best overall user experience. If you don't know what beam makes the most sense, click here.

4" Narrowed is in Stock.

There are three ways to lower your 1966 through 1977 Type 1. Good, Better, Best.

Good
- Install a pair of adjusters, based on budget and skill set - no tech support
Better - Install an Ultimate Beam - Tech Support Included
Best - Install an assembled beam like the Stage 1 PRObuilt Beam - Tech Support Included

Made in the USA | Product updated 6/18/23 by Pete

Typical time to install - 4 Hours | Install PDF Link | Install Video |
Tools Needed

More Information

Null

Normally In stock - Will Ship ASAP
Normal Price $941.95
Airkewld Army Price $856.32 Each
9 in stock!
(19)
Ultimate Adjustable VW Front Link Pin Beam - 2102 Ultimate Adjustable VW Front Link Pin Beam - 2102

A better way to lower a Classic Volkswagen Type 1 with link pin front suspension (1949 through 1965) other than utilizing adjusters in the center of the beam is to order an Ultimate Adjustable Front Beam.

The Ultimate Beam (UB) allows you to adjust your ride height from stock height down to *seven inches on average. The UB has Delrin bushings, a steering dampener bracket, and grease-able zerks. The UB can come in stock width, up to 4" narrowed with shock towers. New torsions, tie rods, and shocks are recommended for the best overall user experience. If you don't know what beam makes the most sense, click here. This beam replaces the factory beam part number 113401021A.

4" Narrowed and Stock Width LHD are in stock


There are three ways to lower your 1949 through 1965 Type 1. Good, Better, Best.

Good
- Install a pair of adjusters, based on budget and skill set - no tech support
Better - Install an Ultimate Beam - Tech Support Included
Best - Install an assembled beam like the Stage 1 PRObuilt Beam - Tech Support Included

Made in the USA | Product updated 8/14/23 by Pete

Typical time to install - 4 Hours | Install PDF Link | Install Video |
Tools Needed

More Information

Null

Normally In stock - Will Ship ASAP
Normal Price $913.28
Airkewld Army Price $830.25 Each
10 in stock!
(16)
6 Inch Ultimate Narrowed / Adjustable Shockless VW Ball Joint Front Beam - 2112 6 Inch Ultimate Narrowed / Adjustable Shockless VW Ball Joint Front Beam - 2112

A better way to lower a Classic Volkswagen Type 1 with ball joint front suspension (1966 through 1977) other than utilizing adjusters in the center of the beam is to order an Ultimate Adjustable Front Beam.

The Ultimate Beam (UB) allows you to adjust your ride height from stock height down to *seven inches on average. The UB has Delrin bushings, a steering dampener bracket, and grease-able zerks. The UB showcased here is six inch narrowed, without shock towers (ultra smooth ride). New torsions, and tie rods, are recommended for the best overall user experience. If you don't know what beam makes the most sense, click here.

There are three ways to lower your 1966 through 1977 Type 1. Good, Better, Best.

Good
- Install a pair of adjusters, based on budget and skill set - no tech support
Better - Install an Ultimate Beam - Tech Support Included
Best - Install an assembled beam like the Stage 1 PRObuilt Beam - Tech Support Included

Made in the USA | Product updated 6/18/23 by Pete

Typical time to install - 4 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $843.15
Airkewld Army Price $766.50 Each
10 in stock!
(2)
6 Inch Ultimate Narrowed / Adjustable Shockless VW Link Pin Front Beam - 2118 6 Inch Ultimate Narrowed / Adjustable Shockless VW Link Pin Front Beam - 2118

A better way to lower a Classic Volkswagen Type 1 with link pin front suspension (1949 through 1965) other than utilizing adjusters in the center of the beam is to order an Ultimate Adjustable Front Beam.

The Ultimate Beam (UB) allows you to adjust your ride height from stock height down to *seven inches on average. The UB has Delrin bushings, a steering dampener bracket, and grease-able zerks. The UB showcased here is six inch narrowed, without shock towers (ultra smooth ride). New torsions, tie rods, and shocks are recommended for the best overall user experience. If you don't know what beam makes the most sense, click here. This beam replaces the factory beam part number 113401021A.

There are three ways to lower your 1949 through 1965 Type 1. Good, Better, Best.

Good
- Install a pair of adjusters, based on budget and skill set - no tech support
Better - Install an Ultimate Beam - Tech Support Included
Best - Install an assembled beam like the Stage 1 PRObuilt Beam - Tech Support Included

Made in the USA | Product updated 6/18/23 by Pete

Typical time to install - 4 Hours | Install PDF Link | Install Video | Tools Needed

More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $813.27
Airkewld Army Price $739.34 Each
10 in stock!
(3)
Stage 1 PRObuilt Adjustable Ball Joint Beam Complete - 2200 Stage 1 PRObuilt Adjustable Ball Joint Beam Complete - 2200

The BEST way to adjust a Classic Volkswagen Type 1 with ball joint front suspension (1966 through 1977), up or down, is by installing a Complete PRObuilt Beam. When the PRO's say complete, they mean complete. You will not need anything in addition to this assembly.

The Stage 1 PRObuilt Beam is built on the Ultimate Beam platform. It's made in stock width and up to four inches narrower than OEM to allow for wider wheels, drop spindles, and disc brakes, that add track width.

The complete beam comes as you see it, spindle to spindle, with an entire PRObuilt steering system installed and ready to bolt in and go. For a full list of details included with the beam assembly, visit the Complete Details section here.

Made in the USA | Product updated 6/14/23 by Pete

Typical time to install - 2 1/2 Hours | Install PDF Link | Install Video | Tools Needed

More Information
Null

12 Weeks on Average
Normal Price $3,325.95
Airkewld Army Price $3,023.59 per Assembly

(8)
Stage 1 PRObuilt Adjustable Link Pin Beam Complete - 2201 Stage 1 PRObuilt Adjustable Link Pin Beam Complete - 2201

The BEST way to adjust a Classic Volkswagen Type 1 with link pin front suspension (1949 through 1965), up or down, is by installing a Complete PRObuilt Beam. When the PRO's say complete, they mean complete. You will not need anything in addition to this assembly.

The Stage 1 PRObuilt Beam is built on the Ultimate Beam platform. It's made in stock width and up to four inches narrower than OEM to allow for wider wheels, drop spindles, and disc brakes, that add track width.

The complete beam comes as you see it, spindle to spindle, with an entire PRObuilt steering system installed and ready to bolt in and go. For a full list of details included with the beam assembly, visit the Complete Details section here. This beam replaces the factory beam part number 113401021A.

Made in the USA | Product updated 6/15/23 by Pete

Typical time to install - 2 1/2 Hours | Install PDF Link | Install Video | Tools Needed

More Information
Null

12 Weeks on Average
Normal Price $3,643.34
Airkewld Army Price $3,312.13 per Assembly

(10)
Stage 2 PRObuilt Air Ride Link Pin Beam Complete - 2202 Stage 2 PRObuilt Air Ride Link Pin Beam Complete - 2202

The BEST way to Air Ride a Classic Volkswagen Type 1 with link pin front suspension (1949 through 1965), is by installing a Stage 2 PRObuilt Beam. When the PRO's say complete, they mean complete. You will not need anything in addition to this assembly.

The Stage 2 PRObuilt Beam is built on the Ultimate Beam platform. It's made in stock width and up to four inches narrower than OEM to allow for wider wheels, drop spindles, and disc brakes, that add track width.

The complete beam comes as you see it, spindle to spindle, with an entire PRObuilt steering system installed and ready to bolt in and go. For a full list of details included with the beam assembly, visit the Complete Details section here.

Made in the USA | Product updated 6/15/23 by Pete

Typical time to install - 3 Hours | Install PDF Link | Install Video | Tools Needed

More Information

Null

12 Weeks on Average
Normal Price $3,577.27
Airkewld Army Price $3,252.06 per Assembly
Stage 2 PRObuilt Air Ride Ball Joint Beam Complete - 2203 Stage 2 PRObuilt Air Ride Ball Joint Beam Complete - 2203

The BEST way to add Air Ride to a Classic Volkswagen Type 1 with ball joint front suspension (1966 through 1977), is by installing a Stage 2 PRObuilt Beam. When the PRO's say complete, they mean complete. You will not need anything in addition to this assembly.

The Stage 2 PRObuilt Beam is built on the Ultimate Beam platform. It's made in stock width and up to four inches narrower than OEM to allow for wider wheels, drop spindles, and disc brakes, that add track width.

The complete beam comes as you see it, spindle to spindle, with an entire PRObuilt steering system installed and ready to bolt in and go. For a full list of details included with the beam assembly, visit the Complete Details section here.

Made in the USA | Product updated 6/17/23 by Pete

Typical time to install - 3 Hours | Install PDF Link | Install Video | Tools Needed

More Information

Null

12 Weeks on Average
Normal Price $3,381.26
Airkewld Army Price $3,073.87 per Assembly

(4)
PRObuilt Transaxle Freeway Flyer - Short Axle - 2300 PRObuilt Transaxle Freeway Flyer - Short Axle - 2300

The BEST way to enjoy the shifting experience and low RPMs at higher speeds in 1949 through 1965 Classic Volkswagen Type 1 Beetle and Karmann Ghia is with a PRObuilt Freeway Flyer Transaxle equipped with *OEM sized Short Axle/Short Spline Axles (SASS). *(It can fit others, see the Complete Details section for more information).

This transaxle is Perfect for the Cruiser application. Key features of this transaxle are the 3.88 Ring and Pinion, overdrive 4th, new synchros, bearings, and seals in a rebuilt SASS 12-volt platform. All transaxles from the PRO's are 12 volt and do not come with OIL. The PRO's recommend
this oil from LAT or this on Amazon. You will need 3.5 quarts usually.

The PRO's offer a few different transaxles with varying lengths of the axle. This allows us to fit wheels with different offsets onto cars, whereas they wouldn't usually fit. So you should pick out your wheels first, run them by the PRO's to see what axle length makes sense, then choose a Cruiser application (Freeway Flyer) or Performance application (not racing but more aggressive driving). No Core is Needed.

Assembled in the USA | Product updated 6/24/23 by Pete

Typical time to install - 6 Hours | Install PDF Link | Install Video| Tools Needed


More Information


Null

12 Weeks on Average
Normal Price $3,219.64
Airkewld Army Price $2,926.95 Each

(2)
VW Link Pin Torsion Leaves - 2400 VW Link Pin Torsion Leaves - 2400

Classic Volkswagen Type 1's have an axle beam up front, and inside that beam are Torsion Leaves. They are also known as Torsion Leaf, Torsions, Torsion Springs, Torsion Slats, Torsion Bars, or the OEM part number for the link pin application is 111411027. There is an upper and a lower needed for each vehicle.

Each tube houses eight leaves, four wide and four small, two on top and two on the bottom. They form a square shape.

One thing to remember when dealing with suspension is AGE. Since the ball joint suspension was born in 1949 (yes they were built earlier, chances are you don't have one of those), these torsion leaves can be up to 74 years old (2023) and have lost spring tension, causing the vehicle to sag over time. So although you might have a stock condition suspension set up, it is a certainty that your Classic VW has lowered over time.

Small note, the Classic Volkswagen Beetle had about six inches or 150mm of a gap between the top of the 165sr15 tire and the fender when it came off the showroom floor.

These torsions come from Volkswagen of Mexico and are NEW, not used. They are offered stock widths up to six inches narrower.

Made in Mexico | Product updated 6/18/23 by Pete

Typical time to install - 4 Hours | Install PDF Link | Install Video | Tools Needed

More Information

Null

Normally In stock - Will Ship ASAP
Normal Price $132.79
Airkewld Army Price $120.72 Each

(5)
VW Ball Joint Torsion Leaves - 2401 VW Ball Joint Torsion Leaves - 2401

Classic Volkswagen Type 1 and Type 181 have an axle beam up front, and inside that beam are Torsion Leaves. They are also known as Torsion Leaf, Torsions, Torsion Springs, Torsion Slats, Torsion Bars, or the OEM part number for the ball joint application is 131411107A. There is an upper and a lower needed for each vehicle.

Each tube houses ten leaves, four wide and six small, three on top and three on the bottom. They form a hexagonal shape.

One thing to remember when dealing with suspension is AGE. Since the ball joint suspension was born in 1966, these torsion leaves can be up to 57 years old (2023) and have lost spring tension, causing the vehicle to sag over time. So although you might have a stock condition suspension set up, it is a certainty that your Classic VW has lowered over time.

Small note, the Classic Volkswagen Beetle had about six inches or 150mm of a gap between the top of the 165sr15 tire and the fender when it came off the showroom floor.

These torsions come from Volkswagen of Mexico and are NEW, not used. They are offered stock widths up to six inches narrower.

Made in Mexico | Product updated 6/18/23 by Pete

Typical time to install - 4 Hours | Install PDF Link | Install Video | Tools Needed

More Information

Null

Normally In stock - Will Ship ASAP
Normal Price $132.79
Airkewld Army Price $120.72 Each

(8)
2-4 Inch Narrowed Link Pin Tie Rods - 2420 2 - 4 Inch Narrowed Link Pin Tie Rods - 2420

To get proper Ackerman, you need to have the right length of tie rods when you narrow your beam. It is not as simple as cutting your tie rods the amount you narrowed your beam. It's a math problem.

For reference, your steering box is not in the center of the beam. It is to the left here in the US. So the lengths of the tie rods play a major role in steering geometry. So, to not give away our secrets, let's just say we have done the math for you.

These tie rods are narrowed enough to allow for two to four inches of narrowed width on a 1949 through 1965 Type 1 Classic Volkswagen Beetle and Karmann Ghia. For the two inch application, you will have less threads showing on the tie rod ends and for the four inch, you will have more. Stock tie rods consist of part numbers 113415802B and 113415801.

Made in the USA | Product updated 6/18/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video |
Tools Needed

More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $115.43
Airkewld Army Price $104.94 per Pair
10 in stock!
(7)
5-6 Inch Narrowed Link Pin Tie Rods - 2421 5-6 Inch Narrowed Link Pin Tie Rods - 2421

To get proper Ackerman, you need to have the right length of tie rods when you narrow your beam. It is not as simple as cutting your tie rods the amount you narrowed your beam. It's a math problem.

For reference, your steering box is not in the center of the beam. It is to the left here in the US. So the lengths of the tie rods play a major role in steering geometry. So, to not give away our secrets, let's just say we have done the math for you.

These tie rods are narrowed enough to allow for five to six inches of narrowed width on a 1949 through 1965 Type 1 Classic Volkswagen Beetle and Karmann Ghia. For the five inch application, you will have less threads showing on the tie rod ends and for the six inch, you will have more. Stock tie rods consist of part numbers 113415802B and 113415801.

Made in the USA | Product updated 6/18/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $115.43
Airkewld Army Price $104.94 per Pair
10 in stock!
(1)
2-3 Inch Narrowed Ball Joint Tie Rods - 2422 2-3 Inch Narrowed Ball Joint Tie Rods - 2422

To get proper Ackerman, you need to have the right length of tie rods when you narrow your beam. It is not as simple as cutting your tie rods the amount you narrowed your beam. It's a math problem.

For reference, your steering box is not in the center of the beam. It is to the left here in the US. So the lengths of the tie rods play a major role in steering geometry. So, to not give away our secrets, let's just say we have done the math for you.

These tie rods are narrowed enough to allow for two to three inches of narrowed width on a 1966 through 1977 Type 1 Classic Volkswagen Beetle, Karmann Ghia, in a ball joint application. For the two inch application, you will have less threads showing on the tie rod ends and for the three inch, you will have more. Stock tie rods consist of part numbers 131415801B, 131415802C for 1966-68, and 131415801F, 131415802E for 1969-77.

Made in the USA | Product updated 6/18/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $115.43
Airkewld Army Price $104.94 per Pair
10 in stock!
(2)
4-6 Inch Narrowed Ball Joint Tie Rods - 2423 4-6 Inch Narrowed Ball Joint Tie Rods - 2423

To get proper Ackerman, you need to have the right length of tie rods when you narrow your beam. It is not as simple as cutting your tie rods the amount you narrowed your beam. It's a math problem.

For reference, your steering box is not in the center of the beam. It is to the left here in the US. So the lengths of the tie rods play a major role in steering geometry. So, to not give away our secrets, let's just say we have done the math for you.

These tie rods are narrowed enough to allow for four to six inches of narrowed width on a 1966 through 1977 Type 1 Classic Volkswagen Beetle, Karmann Ghia, in a ball joint application. For the four inch application, you will have less threads showing on the tie rod ends and for the six inch, you will have more. Stock tie rods consist of part numbers 131415801B, 131415802C for 1966-68, and 131415801F, 131415802E for 1969-77.

Made in the USA | Product updated 6/18/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $115.43
Airkewld Army Price $104.94 per Pair
10 in stock!
(12)
Narrowed Tie Rod Jam Nuts - 2424 Narrowed Tie Rod Jam Nuts - 2424

The perfect pair for a new set of tie rods, these set of 4 jam nuts that are zinc plated in different colors to differentiate left and right work flawlessly with quality tie rod ends.

Assembled in the USA | Product updated 6/12/23 by Pete

Typical time to install - 1 Hour | Install PDF Link | Install Video | Tools Needed

More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $18.41
Airkewld Army Price $16.74 Set of 4
10 in stock!
(1)
Classic VW Type 1 Link Pin Drum Drop Spindles - 2431 Classic VW Type 1 Link Pin Drum Drop Spindles - 2431

A Good option for installing drop spindles on your 1949 through 1965 Classic Volkswagen Type 1 Beetle and Karmann Ghia for the link pin application is this set of DRUM drop spindles. It will lower your vehicle 2.5" and add 3/8" of track width to each side. They work with either stock drum brakes or our GEN 1 or GEN 2 BAD Series Brakes. These spindles will need to be pressed on and off the vehicle. Early model 2 bolt wheel cylinder backing plates will need a small grind on the back of the spindle where it touches the backing plate. These spindles would replace the factory spindles with part numbers 111405301 and 111405302.

Good - Individually purchase these spindles, based on budget and skill set - no tech support
Best - PRObuilt Drop Drum Spindles - Bolt-On - Tech Support Included

Made in China | Product updated 6/18/23 by Pete

Typical time to install - 5 Hours | Install PDF Link | Install Video | Tools Needed

More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $275.72
Airkewld Army Price $250.65 per Pair
10 in stock!
(5)
Classic VW Type 1 1966-1968 Ball Joint Drum Drop Spindles - 2432 Classic VW Type 1 1966-1968 Ball Joint Drum Drop Spindles - 2432

The best option for installing drop spindles on your 1966 through 1968 Classic Volkswagen Type 1 Beetle and Karmann Ghia for the ball joint application is this set of DRUM drop spindles. It will lower your vehicle 2.5" and add 3/8" of track width to each side. They work with either stock drum brakes or our GEN 1 or GEN 2 BAD Series Brakes. Because these drop spindles were made for later models, the PRO's are including a set of German roller bearings, inner seat and premium outer tie rod ends so that this is a bolt on solution for these years and models. These spindles would replace the factory spindles with part numbers 113405311 and 13405312E.

Assembled in the USA | Product updated 6/18/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video | Tools Needed

More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $357.75
Airkewld Army Price $325.23 per Pair
10 in stock!
(2)
Classic VW Type 1 Ball Joint Drum Drop Spindles - 2433 Classic VW Type 1 Ball Joint Drum Drop Spindles - 2433

The best option for installing drop spindles on your 1969 through 1977 Classic Volkswagen Type 1 Beetle and Karmann Ghia for the ball joint application is this set of DRUM drop spindles. It will lower your vehicle 2.5" and add 3/8" of track width to each side. They work with either stock drum brakes or our GEN 1 or GEN 2 BAD Series Brakes. These spindles would replace the factory spindles with part numbers 113405311 and 13405312E.

Made in China | Product updated 6/18/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video | Tools Needed

More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $254.62
Airkewld Army Price $231.47 per Pair
9 in stock!
(6)
Classic VW Type 1 Ball Joint Disc Drop Spindles - 2434 Classic VW Type 1 Ball Joint Disc Drop Spindles - 2434

The best option for installing drop spindles on your 1969 through 1977 Classic Volkswagen Type 1 Beetle and Karmann Ghia for the ball joint application is this set of DISC drop spindles. It will lower your vehicle 2.5" and add 3/8" of track width to each side. They work with either stock disc brakes or disc brake kits using factory Karmann Ghia style calipers. These spindles would replace the factory stock height spindles with part numbers 113405312D and 113405311D.

Made in China | Product updated 6/18/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video | Tools Needed

More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $254.62
Airkewld Army Price $231.47 per Pair
10 in stock!
(2)
Classic VW PRObuilt Link Pin Drum Drop Spindles - 2441 Classic VW PRObuilt Link Pin Drum Drop Spindles - 2441

The Best option for installing drop spindles on your 1949 through 1965 Classic Volkswagen Type 1 Beetle and Karmann Ghia for the link pin application is this set of PRObuilt DRUM Drop Spindles. It will lower your vehicle 2.5" and add 3/8" of track width to each side. They work with either stock drum brakes or our GEN 1 or GEN 2 BAD Series Brakes. Early model 2 bolt wheel cylinder backing plates will need a small grind on the back of the spindle where it touches the backing plate. These spindles would replace the factory spindles with part numbers 111405301 and 111405302.

Good - Individually purchase these spindles, based on budget and skill set - no tech support
Best - PRObuilt Drop Drum Spindles - Bolt-On - Tech Support Included

Assembled in the USA | Product updated 6/18/23 by Pete

Typical time to install - 2 Hours | Install PDF Link | Install Video | Tools Needed

More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $776.86
Airkewld Army Price $706.24 per Pair
10 in stock!
(6)
Classic VW Type 1 Link Pin Adjusters  - 2450 Classic VW Type 1 Link Pin Adjusters - 2450

A good way to lower a Classic Volkswagen Type 1 Beetle or Karmann Ghia with link pin front suspension ( 1949 through 1965) is utilizing adjusters in the center of the beam.

These adjusters will give you the ability to adjust your VW up and down a total of 7.5" when installed at 25 degrees up from parallel to the ground. This means you can go up to stock height at the highest setting and the ability to go down a total of 7.5", but you can set it anywhere you want within that range.

Do not believe the 50/50 garbage out there, it is a Band-aid idea that will only cause more harm. Your factory link pin suspension is designed to be at a stock height, with the arms at a 60 degree angle. The top arm is bottomed out on the stop, the stock shock is maxed out in extension and this is all assumed, that the factory torsions haven't lost any spring tension. (Theortically, if the 50/50 method was put in place with relaxed torsions, you are putting more stress on them to index them higher giving the vehicle an unstable ride. Would it lift it to stock height? Maybe. Would it be good advice to do this to keep your family safe? No.) Installing these adjusters at 25 degrees give you the best use of travel within the range of the factory working components.


There are three ways to lower your 1949 through 1965 Type 1. Good, Better, Best.

Good
- Install these adjusters, based on budget and skill set - no tech support
Better - Install an Ultimate Beam - Tech Support Included
Best - Install an assembled beam like the Stage 1 PRObuilt Beam - Tech Support Included

Made in the USA | Product updated 6/19/23 by Pete

Typical time to install - 12 Hours | Install PDF Link | Install Video |
Tools Needed

More Information

Null

Normally In stock - Will Ship ASAP
Normal Price $90.71
Airkewld Army Price $82.46 Each
10 in stock!
(4)
Classic VW Type 1 Ball Joint Adjusters - 2451 Classic VW Type 1 Ball Joint Adjusters - 2451

A good way to lower a Classic Volkswagen Type 1 Beetle, Karmann Ghia or Type 181 Thing with ball joint front suspension ( 1966 through 1977) is utilizing adjusters in the center of the beam.

These adjusters will give you the ability to adjust your VW up and down a total of 7.5" when installed at 25 degrees up from parallel to the ground. This means you can go up to stock height at the highest setting and the ability to go down a total of 7.5", but you can set it anywhere you want within that range.

Do not believe the 50/50 garbage out there, it is a Band-aid idea that will only cause more harm. Your factory ball joint suspension is designed to be at a stock height, with the arms at a 60 degree angle. The stock shock is maxed out in extension and this is all assumed, that the factory torsions haven't lost any spring tension. (Theoretically, if the 50/50 method was put in place with relaxed torsions, you are putting more stress on them to index them higher giving the vehicle an unstable ride. Would it lift it to stock height? Maybe. Would it be good advice to do this to keep your family safe? No.) Installing these adjusters at 25 degrees give you the best use of travel within the range of the factory working components.


There are three ways to lower your 1966 through 1977 Type 1 and 181. Good, Better, Best.

Good
- Install these adjusters, based on budget and skill set - no tech support
Better - Install an Ultimate Beam - Tech Support Included
Best - Install an assembled beam like the Stage 1 PRObuilt Beam - Tech Support Included

Made in the USA | Product updated 6/19/23 by Pete

Typical time to install - 12 Hours | Install PDF Link | Install Video |
Tools Needed

More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $90.97
Airkewld Army Price $82.70 Each
10 in stock!
(5)
PRObuilt VW Ball Joint Arm Set - 2455 PRObuilt VW Ball Joint Arm Set - 2455

Rebuilding your late model 1966 through 1977 Classic Volkswagen Beetle and Karmann Ghia with ball joint front suspension can be challenging. But the PRO's can give you confidence knowing you are getting the right part, built the right way, and keeping you and your family safe. Our PRObuilt Arm Set gives you that peace of mind.

The OEM VW arms used for this set include these part numbers; 131405103A, 131405104A, 131405151A, and 131405152A. They go through an extensive process to ensure our PRO's put their stamp of quality on the PRObuilt Arm Set. The complete details section will go through all the detail in length.

Assembled in the USA | Product updated 6/19/23 by Pete

Typical time to install - 4 Hours | Install PDF Link | Install Video | Tools Needed

More Information

Null

Normally In stock - Will Ship ASAP
Normal Price $509.29
Airkewld Army Price $462.99 Set of 4
6 in stock!
(10)
German King Pin Kit - 2460 German King Pin Kit - 2460

Fits the following:

  • 1949-1965 US Spec Type 1 Beetle-Bug-Fusca
  • 1949-1965 US Spec Karmann Ghia
  • Kit cars with link pin suspensions
The PRO's Recommendations:
  • Must use the proper reamer to install these

Null

Normally In stock - Will Ship ASAP
Normal Price $80.44
Airkewld Army Price $73.13 Each
German Link Pin Kit - 2461 German Link Pin Kit - 2461

Fits the following:

  • 1949-1965 US Spec Type 1 Beetle-Bug-Fusca
  • 1949-1965 US Spec Karmann Ghia
  • Kit cars with link pin suspensions
The PRO's Recommendations:
  • ARP Stainless Steel Hardware
Tips:
  • Some control arms ends are flat and others are contoured for an o-ring. Do not use the o-rings and dust shields if you control arms are flat.

Null

Normally In stock - Will Ship ASAP
Normal Price $114.81
Airkewld Army Price $104.37 Each
Ball Joint Lowered Eccentrics - 2462 Ball Joint Lowered Eccentrics - 2462

Aligning your late model 1966 through 1977 Classic Volkswagen Beetle and Karmann Ghia with ball joint front suspension can be challenging. But the PRO's can give you confidence knowing you are getting the right part, built the right way, and keeping you and your family safe. Our set of Lowered Eccentrics gives you that peace of mind.

The OEM VW eccentrics used are part number 131405319.

Made in China | Product updated 6/19/23 by Pete

Typical time to install - 1 Hour | Install PDF Link | Install Video | Tools Needed

More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $66.12
Airkewld Army Price $60.11 per Pair
9 in stock!
(4)
OEM PRObuilt Steering Box - 2480 OEM PRObuilt Steering Box - 2480

The most often neglected part of the Classic Volkswagen Drive-Train is the Steering Box. The 113415061C, which is the factory OEM part number, is the most common steering box used. It will work with *All Type 1's, Type 3's, Type 181's and anything that came with a Ball Joint front suspension.

Adjusting the steering box with the adjustment on the top of the box is often over used. As a whole, the steering box is responsible to 40% of the steering wheel play/creep in the steering system. Crazy, right? There is SO MUCH MORE that is responsible for play/creep but we as consumers assume, the steering box is the reason. Let's get into the grease and bearings of the subject...

Made in the USA | Product updated 9/25/23 by Pete

Typical time to install - 4 Hours | Install PDF Link | Install Video |
Tools Needed


More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $715.80
Airkewld Army Price $650.73 Each
8 in stock!
(17)
Lowered Link Pin Front Shock - Sport - 2491 Lowered Link Pin Front Shock - Sport - 2491

These shocks fit the Classic Volkswagen Type 1 Beetle and Karmann Ghia with a link pin front suspension. Shock absorbers are without a doubt the brains of your suspension. Nothing influences how your car rides and handles more than its shock absorbers.

Two kinds of shocks are provided for our clients. They are all designed to work with our Ultimate Beam's ONLY. They will NOT work with other beams including the stock beam. These shocks replace the factory shocks with part number 113413031B.

Sport - Soft riding shock great for a lowered VW.
Adjustable - Tunable shock great for the enthusiast that like to get a specific ride out of their VW.

Made in the USA | Product updated 6/20/23 by Pete

Typical time to install - 1 Hour | Install PDF Link | Install Video |
Tools Needed


More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $99.26
Airkewld Army Price $90.24 Each
12 in stock!
(2)
Lowered Ball Joint Front Shock - Sport- 2493 Lowered Ball Joint Front Shock - Sport- 2493

These shocks fit the Classic Volkswagen Type 1 Beetle, Karmann Ghia and Type 181 Thing with a ball joint front suspension. Shock absorbers are without a doubt the brains of your suspension. Nothing influences how your car rides and handles more than its shock absorbers.

Two kinds of shocks are provided for our clients. They are all designed to work with our Ultimate Beam's ONLY. They will NOT work with other beams including the stock beam. These shocks replace the factory shocks with part number 113413031E.

Sport - Soft riding shock great for a lowered VW.
Adjustable - Tunable shock great for the enthusiast that like to get a specific ride out of their VW.

Made in the USA | Product updated 6/20/23 by Pete

Typical time to install - 1 Hour | Install PDF Link | Install Video |
Tools Needed


More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $99.26
Airkewld Army Price $90.24 Each
8 in stock!
(2)
Ultimate Link Pin Beam Installation Kit - 2550 Ultimate Link Pin Beam Installation Kit - 2550

The Ultimate "No-Brainer" when it comes to rebuilding your 1949 through 1965 Classic Type 1 Volkswagen Beetle or Karmann Ghia link pin front axle beam is this Installation Kit. It will work with an OEM Beam or an Ultimate Beam.

Premium tie rod ends, steering damper, beam bolts, rubber body pads and inspection plate and seal make the rebuilding process a breeze!

Assembled in the USA | Product updated 6/21/23 by Pete

Typical time to install - 4 Hours | Install PDF Link | Install Video |
Tools Needed

More Information
Null

Normally In stock - Will Ship ASAP
Normal Price $230.13
Airkewld Army Price $209.21 per Kit
10 in stock!
(2)